AM550C-06,KAM550-06,SAM550-06,YAM550-06,YAM250-03D,SMC型油霧分離處理器

油霧分離器壓力調節時，在轉動旋鈕前請先拉起再旋轉，壓下旋轉鈕為定位。調節壓力時應逐步均勻地調至所需壓力值，不應一步調節到位。

如氣缸、氣動馬達、蒸汽機等。氣動元件是一種動力傳動形式，亦為能量轉換裝置，利用氣體壓力來傳遞能量。沒有脈動阻尼器時，背壓閥將隨著每次泵沖程的進行而快速打開和關閉。除去壓縮空氣中的油、水、固態物等污染物，提高下游干燥器的功能，延長精密 過濾器的壽命，防止元件出現故障。

使用流體壓縮空氣*高使用壓力1.0MPa

注1*低使用壓力0.05MPa

環境和流體溫度5~60°C

過渡精度xm(去除95%)

二次側油霧濃度

注2)

*多1.0mg/m2(ANR) (=0.8ppm)

濾芯壽命當壓力達到0.1MPa或使用2年時

注1)使用自動排水器時，工作壓力要在0.15MPa以上

注2)壓縮機排放油濃度為30mg/m2(ANR)時。

Z1S6A1-30,Z1S6A2-30,Z1S6A3-30B,Z1S6D1-30/V,疊加式單向閥

Z1S10B1-30,Z1S10B2-30B,Z1S10B3-30，Z1S10T-30B/，

Z1S6F1-30,Z1S6F2-30,Z1S6F3-30B，Z1S6D-30B/，

Z1S10P1-30,Z1S10P2-30,Z1S10P3-30B，Z1S16D-30B/，

Z1S10C1-30B,Z1S10C2-30,Z1S10C3-30，Z1S6P-30B/，

Z1S6D1-30B,Z1S6D2-30,Z1S6D3-30，Z1S6T-30B/，

Z1S6A1-30B/,Z1S6B1-30B/,Z1S6C1-30B/,Z1S6F-30B/，

Z1S6D1-30B/,Z1S6E1-30B/,Z1S6F1-30B/,Z1S6E-30B/，

Z1S6P1-30B/,Z1S6T1-30B/,Z1S6A2-30B/V,Z1S6C-30B/，

Z1S6B2-30B/V,Z1S6C2-30B/V,Z1S6D2-30B/V,

Z1S6E2-30B/V,Z1S6F2-30B/V,Z1S6P2-30B/V,

Z1S6T2-30B/V,Z1S6T1-3X/V,Z1S10T1-3X,Z1S6B-30B/，

Z1S10T1-3X,Z1S10T1-3X/V,Z1S16F1-1X/V,Z1S6A-30B/,

Z1S16P1-3X/V,Z1S10T2-30B/,Z1S10P1,Z1S10D-30B/，

Z1S10T-1-30,Z1S6T-1-30,Z1S10P1-3X/V,

Z2FS-6-2-44/2QV